lh series chip type, high voltage. high reliability. chip type, high voltage and high reliability. load life of 4000 hours at +125 c. applicable to automatic mounting machine using carrier tape. adapted to the rohs directive (2011/65/eu). specifications performance characteristics item lh series voltage(2g : 400v) lot no. plastic platform 0.3max. d0.5 b0.2 a 0.2 a0.2 c0.2 0.5max. e h positive negative u 1 l 2 h 3 2 4 g 5 5 6 r 7 6 8 m 9 n 10 l 11 1 12 g 13 s 14 configuration taping code capacitance tolerance ( 20%) rated capacitance ( 5.6f ) rated voltage ( 400v ) series name type l1.0 8 10 d l a b c e 2.9 8.3 8.3 3.1 10 10 3.2 10.3 10.3 4.5 10 13.5 3.2 10.3 10.3 4.5 l 10 10 13.5 h 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 (mm) trade mark a2 5.6 2g lh pressure relief vent capacitance chip type ( 8 10l, 10) type numbering system (example : 400v 5.6 f) aluminum electrolytic capacitors lt category temperature range 40 to +125 c rated voltage range 160 to 450v rated capacitance range 2.2 to 27f 20% at 120hz, 20 c capacitance tolerance measurement frequency : 120hz the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 4000 hours at 125 c. z 40 c / z+20 c rated voltage (v) impedance ratio zt / z20 (max.) 160 6 200 6 250 10 400 10 450 15 rated voltage (v) tan (max.) 160 0.20 200 0.20 250 0.25 400 0.25 450 0.30 measurement frequency : 120hz at 20 c capacitance change leakage current tan within 30% of the initial capacitance value less than or equal to the initial specified value 300% or less than the intial specified value leakage current tangent of loss angle (tan ) stability at low temperature endurance the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the characteristic requirements listed at right when they are removed from the plate. black print on the case top. after storing the capacitors under no load at 125 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value shelf life resistance to soldering heat marking after 1 minute's application of rated voltage, leakage current is not more than 0.04cv+100 (a). taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please refer to page 3 for the minimum order quantity. dimensions 2.2 3.3 3.9 5.6 7.5 10 12 15 18 22 27 2r2 3r3 3r9 5r6 7r5 100 120 150 180 220 270 8 10 10 10 10 13.5 8 10 10 10 10 13.5 8 10 10 10 10 13.5 8 10 10 10 10 13.5 8 10 10 10 10 13.5 45 60 65 45 60 65 30 45 50 30 45 50 20 35 40 2c 2d 2e 2g 2w 160 200 250 400 450 v code cap.(f) rated ripple case size d l (mm) frequency coefficient of rated ripple current coefficient frequency 50 hz 0.70 1.00 1.17 1.36 1.50 120 hz 300 hz 1 khz 10 khz or more rated ripple current (marms) at 125 c 120hz long life voltage v 160 200 250 400 450 code 2c 2d 2e 2g 2w cat.8100c
|
